Page 1 of 2

Parts replacement on my A-bike

PostPosted: Wed Nov 07, 2007 4:40 am
by Amuro Lee
As an over-weight A-biker (115kg :oops:), my A-bike has been torturing by me for a whole year.

After a year of heavy duty on my little A-bike, the middle part of the tread of the rear tyre have been worn away.
Image
Image

There's a crack appearing on the rear lower tube, too.
Image
Image

When I tried to go up a steep incline by my A-bike last week, the chain fell off from the gear suddenly. After opening the crank case, a crack has been found on the small spocket of the layshaft.
Image

Therefore, I had to replace the following parts:
Image

Here are the prices of the parts from MHM, the local distributor of A-bike in Hong Kong.
Rear Lower Tube: HK$500
Layshaft: HK$125

得把口, an A-bike expert in the local A-bike community, has helped me to replace those parts. We just did it openly in a park last night. :P
Image
Image

My A-bike is recovered now.
Image

Redundant parts
Image

PostPosted: Wed Nov 07, 2007 12:51 pm
by newcross
Thank you for your report Amuro. I also experienced the crack on the tube and got parts from Mayhem then replaced it by myself (but new crack starting to appear...now it's about 5mm length.)

My case.

I found a hairline crack one day and it became bigger and bigger. I continued riding, the rear tube quick release clip snapped and whole thing got wobbly. Angle of the saddle and everything gone wrong. Please see below animation GIF I made. (I guess quick release was unclipped by my trousers then rear metal tube couldn't take the load with having the hairline crack, so the pipe started to tear and the crack opened, then a single screw of quick release was snapped by the force.
Image
Since the rear upper tube is held by two button catches, my A-bike was somewhat ridable for a while even though it was very unstable --- so I could ride up to nearby pavement to save myself from cars. However, I saw reasonable numbers of reports on the crack on the net and thought there is a possible risk of fatal accident if users don't replace the cracked rear tube for long time.

(img. hairline crack on my A-bike)
Image
(img. right after the incident. The opening of the crack was much bigger, but I pushed it back a little when I took this photo.)
Image

PostPosted: Wed Nov 07, 2007 1:04 pm
by newcross
As far as I reckon, the crack will appear soon or later if your use A-bike regularly, even you take good care of your bike.

over tightening quick release clamp is absolute no-no. Although this cannot be the only cause for the crack, but this surely encourages the crack.

I already reported this cracking problem in document to Mayhem, Alex. K., Sir Clive at the London Meeting July 2007. Hopefully they will come up with some solutions.

PostPosted: Mon Nov 19, 2007 7:45 pm
by Amuro Lee
I found this picture on the post of disney's 3rd day journey on Jeju Island on the Naver Abike Cafe.
http://cafe.naver.com/dakaabike/2835

Image

I think this is a good method to prevent the situation get worse.

PostPosted: Tue Nov 20, 2007 2:00 am
by the other Guest
Sorry me derailing. Not sure how to reach New Cross in any other way.

New Cross, is that an official CAD? based on A-bike site or did you do that one yourself. Looks so great to me who have no knowledge of how to make such.

I wish me could make such pictures too.

I refer to this one

00anime.gif as a guest I am not allowed to make such links

Which program does one need and do they save in gif or does one need a converter program to do that?

If you don't want to answer here in thred to write to

gaius.b at hotmail dot com

PostPosted: Tue Nov 20, 2007 4:37 am
by newcross
the other Guest wrote:New Cross, is that an official CAD? based on A-bike site or did you do that one yourself. Looks so great to me who have no knowledge of how to make such.
I wish me could make such pictures too.
I refer to this one
00anime.gif as a guest I am not allowed to make such links
Which program does one need and do they save in gif or does one need a converter program to do that?


Hi, the image looks great because the official A-bike image was great. I captured it from A-bike official online manual and altered it to simulate the incident by using photo editing software. "Animated GIF" canbe easily created by using freewares. To paste images (including GIF) here, you need to upload the image to a server (could be free photo host like Flickr) then just put the URL with Img tag you can see in the forum posting form.

In anyway, it's always good to register to this forum, so that you can post images and also send private message to other members of the forum. :wink:

PostPosted: Tue Nov 20, 2007 4:47 am
by newcross
Amuro Lee wrote:I found this picture on the post of disney's 3rd day journey on Jeju Island on the Naver Abike Cafe.
http://cafe.naver.com/dakaabike/2835
I think this is a good method to prevent the situation get worse.


Amuro, thank you for re-upload the image to show us the disney's tip. (i still haven't managed to view the article properly :cry: , so this is really nice.) :D

the idea is fantastic!! I shall try this on my A-bike.
however I feel the metal strap should be put higher up to hold against the tube breaking load. :roll:

PostPosted: Tue Nov 20, 2007 4:53 am
by newcross
newcross wrote:however I feel the metal strap should be put higher up to hold against the tube breaking load. :roll:


I just realise it cannot go any further.... mmm... :?

PostPosted: Tue Nov 20, 2007 5:26 am
by Amuro Lee
newcross wrote:
newcross wrote:however I feel the metal strap should be put higher up to hold against the tube breaking load. :roll:

I just realise it cannot go any further.... mmm... :?

Yes, you are right. It cannot go any further... :wink:
Image
(This picture is also copied from the Korean A-bikers' :P)

Another part replacement on my A-bike

PostPosted: Wed Dec 26, 2007 9:14 pm
by Amuro Lee
The Upper Steering Joint Pivot Fixture of my A-bike broke recently. :(
Image
Image
Image
Image
Image
I don't think it's the problem of the A-bike itself because I'm really a seriously overweight person (115kg :oops: ) as the recommended maximum user weight of A-bike is only 85kg and my A-bike has already been tortured by me for a whole year.

I've ordered the part from the local distributor. The price is HK$57 only.
Image
Image
Image
Image

Thanks to 得把口 for helping me to replace the part again!
Image
Image
Image

The broken part
Image
Image
Image

My A-bike is recovered again.
Image
Image

The rear lower tube has been strengthened by installing a stainless steel hose clip on it this time.
Image
Image
Image
Image

PostPosted: Wed Dec 26, 2007 9:40 pm
by kenwshmt2
Should the rest of us do this as a preventative measure?
If we can find some straps that don't look to bad, it would be worth doing I think.

PostPosted: Sat Dec 29, 2007 1:36 am
by Fai
I think I will need Mr 得把口 help one day in the future because I really do not have any idea of how to repair or replace broken part of my A-bike. I would like to know how much is the service provided by Mr 得把口 ? (In the case you show us this time for example) Where is he/his shop?

PostPosted: Sat Dec 29, 2007 9:21 am
by Amuro Lee
Fai wrote:I think I will need Mr 得把口 help one day in the future because I really do not have any idea of how to repair or replace broken part of my A-bike. I would like to know how much is the service provided by Mr 得把口 ? (In the case you show us this time for example) Where is he/his shop?

I've given you his phone number. Do you remember that?
He is just an amateur bike mechanic.
You can phone him directly or e-mail him via lck98596842@yahoo.com.hk

Re: Parts replacement on my A-bike

PostPosted: Mon Jul 19, 2010 11:52 am
by noodbix
I highly suggest everyone should put that metal band called a tube clamp/ring around the rear tube.

For safety purposes, I put the clamp around both tubes near where the locking clasps are. That way, you can prevent any bad things from happening to the bike, short of the plastic breaking.

Re: Parts replacement on my A-bike

PostPosted: Sun Jun 19, 2016 1:05 pm
by rp1733698@gmail.com
Upper Steering Joint Pivot Fixture of my A-bike is been broken so i need a new Upper Steering Joint Pivot Fixture of my A-bike .please, if anyone could help me with this part then please do e-mail at rp1733698@gmail.com